Close
Bulk Purchase - Bonnet absorber for Wira
Started by
drexchan
, Jan 11 2005 12:20 PM, 285 replies to this topic
#271
Posted 11 February 2005 - 12:31 PM
drexchan,
Wah !!!! So much problem one ah !!!!! Have not collected mine yet, can
cancel ???
Thanks.
Wah !!!! So much problem one ah !!!!! Have not collected mine yet, can
cancel ???
Thanks.
#272
Posted 12 February 2005 - 12:53 PM
why cancel? the problem risen from improper lubrication i think.. I'll
install for you (have already changed it, just the faulty unit, not a
pair). This time i'll use grease but not WD40..
install for you (have already changed it, just the faulty unit, not a
pair). This time i'll use grease but not WD40..
#274
Posted 12 February 2005 - 08:45 PM
drexchan,
Pls advice when, since CNY is now over. We could meet at the same place and
time.
Thanks.
Hope mine don't have all the problems.
Pls advice when, since CNY is now over. We could meet at the same place and
time.
Thanks.
Hope mine don't have all the problems.
#276
Posted 23 March 2005 - 11:06 AM
Drex,
sorry for disturbing...
the left sided lifter spoiled lah... it got jammed
is it still under warranty? if not can i get onli the left side lifter
thanx for information
tankl
sorry for disturbing...
the left sided lifter spoiled lah... it got jammed
is it still under warranty? if not can i get onli the left side lifter
thanx for information
tankl
#277
Posted 23 March 2005 - 02:31 PM
if it's only one side, i can help yu to get it replaced. left side
meaning the passenger side? You have got mail.
meaning the passenger side? You have got mail.
#278
Posted 23 March 2005 - 02:37 PM
klkow,
uncle.. your pair is still with me.. when you wanna get them installed?
uncle.. your pair is still with me.. when you wanna get them installed?
#279
Posted 07 April 2005 - 03:58 PM
Halo guys, no wonder your bonnet absorber so fast kong lar, do u guys know
that those absorber with shaft & piston do not require any greasing or
lubricant, once u add did it, u are going to damage it sooner. The factory
comes already being greased inside with special grease.Did u ever seen any
mech do greasing for your suspension`s absorber?
Whoever put WD40 to the shaft, u are kidding, God bless u.
that those absorber with shaft & piston do not require any greasing or
lubricant, once u add did it, u are going to damage it sooner. The factory
comes already being greased inside with special grease.Did u ever seen any
mech do greasing for your suspension`s absorber?
Whoever put WD40 to the shaft, u are kidding, God bless u.
#280
Posted 08 April 2005 - 08:41 AM
wfc31, if what u said is correct hor..then i can only say this bonnet
absorver quality suks...coz already rusting after i open up the bonnet a
few days after installation. During installation, I didnt put anything
also, have to grease it coz after open the bonnet, can see the whole inner
part of the rod already contain rust and cannot close back the bonnet...so
u expect me to drive with the bonnet up ke??? plus...there's no
instruction on the box that says no grease...so, what are we supposed to
do? throw them into the river? anyway, dun care already, will throw it
away if it become worse...
absorver quality suks...coz already rusting after i open up the bonnet a
few days after installation. During installation, I didnt put anything
also, have to grease it coz after open the bonnet, can see the whole inner
part of the rod already contain rust and cannot close back the bonnet...so
u expect me to drive with the bonnet up ke??? plus...there's no
instruction on the box that says no grease...so, what are we supposed to
do? throw them into the river? anyway, dun care already, will throw it
away if it become worse...